New Area 51 Resource Lifts Tunkillia to 1.5 Million oz Gold

PRESS RELEASE
Published June 14, 2024

Platform established for 2024 Scoping Studies and high-grade targeting

ADELAIDE, AUSTRALIA / ACCESSWIRE / June 14, 2024 /

HIGHLIGHTS

  • Tunkillia JORC Mineral Resource Estimate grows to 1.5 million oz (51.3Mt @ 0.91 g/t Au), with a new 115,216 oz Au Mineral Resource at Area 51 (4.98Mt @ 0.72 g/t Au)
  • Broad (50 - 100m) bulk open pittable mineralisation ~3km from main 223 Deposit
  • 3rd Tunkillia JORC update in ~12 months, adding ~530,000oz Au for ~A$15/oz (‘all in' basis); 2024 exploration focused on high-grade neighbouring targets at Tunkillia and Tarcoola
Fig 1 - Tunkillia Area 51 map with MRE outline and drill collars (note holes dip to NE, into MRE)

Barton Gold Holdings Limited (ASX:BGD)(FRA:BGD3)(OTCQB:BGDFF) (Barton or the Company) is pleased to announce an updated JORC Mineral Resources Estimate (MRE) for the Tunkillia Gold Project (Tunkillia).

Approximately 8,663m of drilling by Barton has delivered a new 115,216koz Au Area 51 Deposit to the northwest of the 223 Deposit. Total Tunkillia JORC (2012) Mineral Resources are now estimated at 1,493,000 ounces Au (51.3Mt @ 0.91 g/t Au), with ~55% classified in the ‘Indicated' category.

Commenting on the latest Tunkillia JORC Resources update, Barton MD Alex Scanlon said:

"Barton has now grown Tunkillia's JORC Mineral Resources three times during the past 12 months, with around 530,000 ounces of gold added through the systematic, cost-efficient identification and conversion of new zones.

"The updated 1.5Moz Au Resource provides a critical mass on which to now model baseline economic analyses, while pursuing neighbouring high-grade targets like Tunkillia's Area 191 and Tarcoola. These have significant potential to enhance overall project economics and support Stage 1 development leveraging our existing mill."

Continued growth of Tunkillia JORC MRE

An updated Tunkillia map showing the March 2024 MRE outlines, and regional targets Area 191 and SE Offset, is shown at Figure 2 below. The updated Tunkillia MRE includes a new MRE at Area 51 located northwest of the 223 Deposit. This is the Company's 4rd MRE update for Tunkillia since late 2020, and the 3rd delivered during the past ~12 months for aggregate growth of ~530,000oz Au in that time.

Fig 2 - Tunkillia Project MRE and neighbouring targets (refer to 14 Feb 2024 ASX announcement)

New Area 51 JORC Mineral Resource Estimate (MRE)

Drilling has defined a new 115,216koz Au MRE at Tunkillia's Area 51 zone (4.98Mt @ 0.72 g/t Au). JORC MRE modelling has been restricted to ~150m depth from surface at a 0.5 g/t Au cutoff grade, with a further broad, continuous halo of surrounding mineralisation (modelled on a 0.4 g/t Au cutoff grade).

Fig 3 - Long section of Area 51 Deposit block model showing all mineral domains (looking W/NW)
Table 1 - Area 51 MRE (4 March 2024)

Drilling in new Area 51 MRE

The Area 51 Deposit MRE has been informed by a total of 72 drill holes, including 6,058m of reverse circulation (RC) and 2,605.4m diamond drilling (DD) (total 8,663.4m) completed by Barton.

Continued efficient Tunkillia growth

  • Estimated ~A$2.05m ‘all in' cost at Area 51, averaging ~A$18 / new oz
  • Past 12 months: ~530,000oz Au added for average ~A$15/oz (all in)

Shallow bulk mineralisation

  • Broad (50 - 100m wide) and shallow (~25m - 150m deep) mineralisation
  • Potential source of bulk-efficient mineralisation for later production years and/or blending operations

Background & updated Tunkillia MRE

In 2022 Barton completed 1,926m of RC drilling at Area 51, announcing a new ~500m long gold zone in September 2022 with results including 17m @ 3.20 g/t Au from 77m and 25m @ 1.51 g/t Au from 81m.1

In early 2023 Barton completed a further 2,118m RC and 856.9m DD drilling, announcing the extension of Area 51 to ~700m length in April 2023 with key results including 28.55m @ 1.32 g/t Au from 91.45m.2

During late 2023 Barton completed another 1,700m RC and 1,748.5m DD drilling, intersecting broad mineralisation with results including 44.6m @ 1.81 g/t Au from 64m and 22m @ 1.33 g/t Au from 158m.3

Fig 5 - Area 51 Cross Section 116,150N3

The updated global Tunkillia MRE is shown below at Table 2.

Table 2 -Global Tunkillia MRE (4 March 2024)

The previously reported global Tunkillia MRE (as at 11 December 2023) is shown below at Table 3.

Table 3 - Global Tunkillia MRE (11 December 2023)
Fig 6 - Drilling at Tunkillia during calendar year 2023 MRE growth programs

Updated Global JORC MRE Statement

Further to the new MRE detailed in this announcement for Tunkillia's Area 51 Deposit, Barton's total attributable JORC (2012) Mineral Resource endowment has grown by approximately 8% to a total 1,575koz Au (52.2Mt @ 0.94 g/t Au). Figure 6 below provides the full details of Barton's global MRE endowment.

Table 4 - Barton Global JORC MRE Inventory (March 2024)

* Table shows complete JORC Mineral Resources Estimate (MRE) for each Project on a 100% basis. Figures subject to rounding; tonnages are dry-metric tonnes; all Mineral Resources classified as ‘inferred' are approximate; cut-off grades applied are 0.4 g/t Au (Tunkillia Area 223), 0.5 g/t Au (Tunkillia Area 51), 0.4 g/t Au (Tarcoola), 2.0 g/t Au (Challenger).

Mineral Resource Estimation Methodology and Data

The following information is provided as an addendum and meets the requirements under ASX Listing Rule 5.8.1. This information is provided in detail in the attached JORC Table 1.

Summary

The Area 51 deposit is a satellite deposit approximately 4 km north of the Tunkillia Project. The Tunkillia Project is located 530 km north-west of Adelaide in South Australia's Gawler Craton. It is 100% owned by Tunkillia 2 Pty Ltd which is a wholly owned subsidiary of Barton Gold Holdings Limited.

The Tunkillia Project lies within the Central Gawler Craton of South Australia which is bound to the east by the Gawler Range Volcanic Province. The central portion of the Gawler Craton consists of a variety of geological units and is structurally complex. Archaean metamorphic rocks and greenstone-belt units are distributed along WSW-ENE trends. During the Palaeoproterozoic, granitoids including the Tunkillia Suite were emplaced possibly with associated deformation. During these deformation episodes, major shear zones developed, including the east-trending Yerda and Oolabinnia Shear Zones and the north-trending Yarlbrinda Shear Zone, host to the Area 51 gold deposit. Typical lithologies encountered at the Tunkillia Project (including Area 51, Sutton Hoo, Tunkillia 223 and Tillya Tepe) from west to east include variably sheared chlorite-biotite-rich augen gneiss (Tunkillia Augen Gneiss) grading into a highly chloritised and mylonitised phyllitic shear.

The primary lithologies at Area 51 are the Tunkillia Granite, after a 1690-1670 Ma granite intrusion, and the Tunkillia Augen Gneiss. The deposit is totally enclosed with the Yarlbrinda Shear zone and all lithologies have undergone some level of deformation and alteration, with the extreme end member forming a finely laminated phyllonite grading to a coarser shear foliation designated as mylonite. The large-scale control on mineralisation is strain partitioning within the broader shear zone, associated with sericite alteration and quartz-calcite ± base metal veins either parallel to or at a low angle to the strain partitioning.

The broad bulk of the gold mineralisation is hosted in the NNW trending subvertical shear partition zone, with additional mineralisation in secondary quartz and stockwork vein halos associated with two south-west dipping brittle faults in the footwall and a flat lying supergene horizon where the sub-vertical mineralisation intersects the weathering profile. A poorly mineralised NNW striking fault, the Central A51 Fault, is a late brittle fault generally corresponding to the hanging wall of the deposit and is considered a hard boundary to the mineralisation.

The resource is reported above a depth of 1025 m RL and above a 0.5 g/t gold cut off (1025 m RL is approximately 150 m below the surface).

0.5 g/t cut offIndicatedInferredTotal
tonnes (Mt)Gold (g/t)Gold (koz)tonnes (Mt)Gold (g/t)Gold (koz)tonnes (Mt)Gold (g/t)Gold (koz)
Oxide0.000.0000.20.8750.190.875
Transitional0.000.0001.00.72241.020.7224
Fresh0.930.87262.80.66603.770.7186
Total0.930.87264.10.68894.980.72115

Table A - Area 51 Mineral Resource Estimate 2024

* Due to rounding to appropriate significant figures, minor discrepancies may occur, tonnages are dry metric tonnes.

Mineral Resources are not Ore Reserves and do not have demonstrated economic viability.

Inferred resource have less geological confidence than Indicated resources and should not have modifying factors applied to them. It is reasonable to expect that with further exploration most of the inferred resources could be upgraded to indicated resources.

Geology and geology interpretation

The Tunkillia project is Proterozoic-aged shear hosted gold system located in the central Gawler Craton region of South Australia. The deposit lies within the regional-scale Yarlbrinda shear zone which represents the boundary between several major crustal domains. The deposit has dimensions of approximately 1 km along a north north-westerly strike, with primary zones of mineralisation having a steep west south-westerly dipping orientation. Higher grade zones of mineralisation are primarily hosted within multiple zones of quartz veins, within a broader zone of lower grade gold mineralisation. A significant zone of flat lying gold mineralisation occurs at the base of weathering above fresh rock. No historical mining or prospecting has taken place at the deposit.

Drilling techniques

A total of 72 RC and diamond drill holes for 12,252.4 m have been drilled within the area defined by the A51 a mineral resource. 59 of these holes are RC (9,647 m) with 13 holes (2,605.4 m) being either diamond or pre-collared diamond. Barton Gold's drilling since 2021 comprises 6,058 m RC (35 holes) and 2605.4 m diamond drilling (13 holes). RC drilling for Barton Gold was undertaken by Bullion Drilling Pty Ltd using a Schramm T865 rig and Kenndy Drilling using a custom made SR650 with all RC rigs having on-board compressors with an auxiliary booster to provide approximately 2000cfm by 1000psi. Diamond drilling completed by Resolution Drilling using a UDR1200 rig.

Drill holes across the deposit are spaced at nominal 50 m x 25 m centres. Pierce point intersections are similarly achieved at 50 m vertical centres.

The locations of historical drill holes have been verified by Barton Gold with both surface drill collar pick-ups and by validation of existing mineralisation with a recent drill program.

Sampling and sub-sampling techniques

RC drilling by Barton Gold utilised a 5 ¾" face-sampling hammer, with a rig-mounted cone splitter attached to the cyclone providing one-metre sample intervals. Field duplicates were collected at the ratios of either 1:16 or 1:22. Certified reference materials (CRMs) sourced from OREAS were inserted with grade ranges suited to grade populations for the deposit.

Diamond drilling by Barton Gold utilised NQ-size drill core, with half-core submitted for analysis. Intervals were generally one metre in length and adjusted where appropriate to reflect geological boundaries. Field duplicates were derived by quarter-coring intervals. Identical field duplicate and CRM protocols as RC drilling were used.

Sample analysis

Two to four kilogram RC splits and half-drill core were sent to Bureau Veritas in Adelaide for preparation and analysis using 40 g fire assay techniques for gold. Bureau Veritas' FA1 method uses a 40 g lead collection fire assay with AAS finish to a 0.01 ppm detection limit. Samples from an earlier phase of Barton Gold drilling were sent to Intertek Genalysis in Adelaide for preparation and analysis using 50 g fire assay techniques for gold and ICPOES/MS for multielement geochemistry.

A variety of analytical techniques and laboratories have been utilised over the course of the project's history and are considered suitable for resource estimation purposes.

QAQC

Barton Gold inserted certified reference materials (CRM's) supplied by OREAS into the sampling sequence every 25 samples. CRM's were selected on the basis of gold levels relevant to the deposit being drilled. Barton Gold's overall QAQC protocols utilised CRM's, field duplicates and certified coarse blank inserted at an overall ratio of one per ten routine drill hole samples for both RC and diamond drilling.

Based on the results of standard analysis, in addition to the internal QA/QC standards, repeats and blanks run by the laboratory, the laboratory was deemed to provide an acceptable level of accuracy and precision.

Estimation methodology

The geological interpretations are based on drill hole data: there is no outcrop in the area covering the deposit. Drill core and RC chip logging has been used to define the main geological units and weathering profile boundaries.

Mineralisation above the base of weathering is assumed to be affected by supergene or weathering effects and is interpreted as dominantly horizontal lenses. Four fresh rock mineralized structures were interpreted, based on continuity of grade at a lower cut-off of 0.35 g/t Au at the A51 deposit. Structures were grouped into geostatistical domains based on grade similarities and structural orientation. A51 strikes grid (local) north-west and dip steeply west.

The Mineral Resource statement reported herein is a reasonable representation of the A51 deposit based on current sampling data. Grade estimation was undertaken using Geovia's Surpac™ software package (v7.7). Ordinary Kriging ("OK") was selected for grade estimation.

The block model utilises parent blocks measuring 10 m x 20 m x 5 m with sub-blocking to 1.25 m x 2.5 m x 1.25 m (XYZ) to better define the volumes. Blocks above topography are flagged as air blocks. Estimation resolution was set at the parent block size.

Informing samples were composited down hole to 1 m intervals. Grade capping was applied to outlier composites. Experimental variograms were generated where possible in Surpac. For domains where experimental variograms could not be created, variogram models were borrowed from similar domains. A two-pass estimation process was employed, the first pass (70 to 90 m search domains dependent) required a minimum of 12 samples and a maximum of 20 composites, the second pass (double pass one) required a minimum of 6 composites and a maximum of 16 composites. Density values are assigned to blocks based on lithology and weathering; the average density of the mineralisation is 2.65 t/m3.

Block model validation consisted of visual checks in plan and section, global comparisons between input and output means, alternative estimation techniques.

Cut-off grades

The resource is reported above a 0.5 g/t gold grade and within 150 m of the surface (1025 mRL).

The following assumptions were considered.

Resource Cut Off Assumptions

Item

Units

Value

Gold Price

AUD$/oz

$3,000

Gold Price

AUD$/g

$ 96.45

Recovery

%

95%

Effective Revenue

AUD$/g

$ 91.63

Less Royalty

%

6.0%

Less per g Costs

AUD$/g

$ 0.96

Realized Revenue

AUD$/g

$ 86.17

Cost to Mine/t ore

AUD$/t

$ 19.23

Costs to Process

AUD$/t

$ 14.00

Cut-off (in place)

g/t

0.39

Dilution

%

5%

Min. Potential Resource Cut-off Grade

g/t

0.41

Criteria used for classification

The Resource Estimates were classified in accordance with the JORC 2012 code. The A51 resources are classified based on data quality, drill density, number of informing samples, kriging efficiency, average distance to informing samples and vein consistency (geological continuity). Geological continuity has been demonstrated at 50 m grid spacing over the entire strike of the deposits. Areas of high grade or geological complexity have been infilled to 25 m grid centres. Areas drill on 50 m sections, with some infilled on 25 m centres down dip are classified as indicated, predicated on geological confidence. Areas of 50 m x 50m or greater have been classified as inferred. Areas of limited geological confidence or at a depth beyond a reasonable open pit depth remains unclassified. A mineral resource is not an ore reserve and does not have demonstrated economic viability.

Mining and metallurgical methods and parameters and other material modifying factors considered to data

Barton Gold foresees mining via open pit and heap or conventional grinding and leach recovery. Mining Associates ("MA") notes that this is a reasonable assumption but should not be regarded as rigorous at this stage of the project. The current Mineral Resource does not include any dilution or ore loss associated with practical mining constraints. The A51 mineralisation sampled has been shown to be amenable to direct cyanidation for gold extraction. Limited metallurgical work shows moderate recovery differences between oxidised and fresh material. Gold recoveries at the Tunkillia Project within the oxidised material are between 92 and 97%.

Authorised by the Board of Directors of Barton Gold Holdings Limited.

For further information, please contact:

Alexander Scanlon
Managing Director
a.scanlon@bartongold.com.au
+61 425 226 649

Shannon Coates
Company Secretary
cosec@bartongold.com.au
+61 8 9322 1587

1 Refer to ASX announcement dated 5 September 2022
2 Refer to ASX announcement dated 19 April 2023
3 Refer to ASX announcement dated 8 February 2024 for further details of drilling intersections

Competent Persons Statements

The information in this announcement that relates to Exploration Results for the Tunkillia Gold Project (including drilling, sampling, geophysical surveys and geological interpretation) is based upon, and fairly represents, information and supporting documentation compiled by Mr Marc Twining BSc (Hons). Mr Twining is an employee of Barton Gold Holdings Ltd and is a Member of the Australasian Institute of Mining and Metallurgy Geoscientists (AusIMM Member 112811) and has sufficient experience with the style of mineralisation, the deposit type under consideration and to the activity being undertaken, to qualify as a Competent Person as defined in the 2012 Edition of the "Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves" (The JORC Code). Mr Twining consents to the inclusion in this announcement of the matters based upon this information in the form and context in which it appears.

The information in this announcement that relates to the estimate of Mineral Resources for the Tunkillia Gold Project geological interpretation and resource estimates) is based upon, and fairly represents, information and supporting documentation compiled by Mr Ian Taylor BSc (Hons). Mr Taylor is an employee of Mining Associates Pty Ltd and has acted as an independent consultant on Barton Gold's Tunkillia Gold Project, South Australia. Mr Taylor is a Fellow and certified Professional of the Australian Institute of Mining and Metallurgy (FAusIMM (CP Geo) 110090) and has sufficient experience with the style of mineralisation, the deposit type under consideration and to the activity being undertaken, to qualify as a Competent Person as defined in the 2012 Edition of the "Australasian Code for Reporting of Exploration Results, Mineral Resources and Ore Reserves" (The JORC Code). Mr Taylor consents to the inclusion in this announcement of the matters based upon this information in the form and context in which it appears.

About Barton Gold

Barton Gold is an ASX listed Australian gold exploration company with a total attributable 1.3Moz Au JORC Mineral Resources endowment (40.6Mt @ 1.0 g/t Au), a pipeline of advanced exploration projects and brownfield mines, and 100% ownership of the only regional gold mill in the central Gawler Craton of South Australia.*

Tarcoola Gold Project

  • Existing brownfield open pit mine within trucking distance of Barton's processing plant
  • Under-explored asset with untapped scale potential

Tunkillia Gold Project

  • 1.15Moz Au Mineral Resources (38Mt @ 0.94 g/t Au)*
  • District-scale structures with advanced satellite targets

Infrastructure

  • 650ktpa CIP process plant, mine village, and airstrip
  • Tarcoola ~40 person lodging to support mine operations
  • Tunkillia camp to support dedicated project team

Competent Persons Statement & Previously Reported Information

The information in this announcement that relates to the historic Exploration Results and Mineral Resources as listed in the table below is based on, and fairly represents, information and supporting documentation prepared by the Competent Person whose name appears in the same row, who is an employee of or independent consultant to the Company and is a Member or Fellow of the Australasian Institute of Mining and Metallurgy (AusIMM), Australian Institute of Geoscientists (AIG) or a Recognised Professional Organisation (RPO). Each person named in the table below has sufficient experience which is relevant to the style of mineralisation and types of deposits under consideration and to the activity which he has undertaken to quality as a Competent Person as defined in the JORC Code 2012.

Activity

Competent Person

Membership

Status

Tarcoola Mineral ResourceDr Andrew Fowler (Consultant)AusIMMMember
Tarcoola Exploration Results (until 15 Nov 2021)Mr Colin Skidmore (Consultant)AIGMember
Tarcoola Exploration Results (after 15 Nov 2021)Mr Marc Twining (Employee)AusIMMMember
Tunkillia Exploration Results (until 15 Nov 2021)Mr Colin Skidmore (Consultant)AIGMember
Tunkillia Exploration Results (after 15 Nov 2021)Mr Marc Twining (Employee)AusIMMMember
Tunkillia Mineral ResourceDr Andrew Fowler (Consultant)AusIMMMember
Challenger Mineral ResourceMr Dale Sims (Consultant)AusIMM / AIGFellow / Member
Western Gawler Craton JV Mineral ResourceMr Richard Maddocks (Consultant)AusIMMFellow

The information relating to historic Exploration Results and Mineral Resources in this announcement is extracted from the Company's Prospectus dated 14 May 2021 or as otherwise noted in this announcement, available from the Company's website at www.bartongold.com.au or on the ASX website www.asx.com.au. The Company confirms that it is not aware of any new information or data that materially affects the Exploration Results and Mineral Resource information included in previous announcements and, in the case of estimates of Mineral Resources, that all material assumptions and technical parameters underpinning the estimates in the Prospectus continue to apply and have not materially changed. The Company confirms that the form and context in which the applicable Competent Persons' findings are presented have not been materially modified from the previous announcements.

Cautionary Statement Regarding Forward-Looking Information

This document may contain forward-looking statements. Forward-looking statements are often, but not always, identified by the use of words such as "seek", "anticipate", "believe", "plan", "expect", "target" and "intend" and statements than an event or result "may", "will", "should", "would", "could", or "might" occur or be achieved and other similar expressions. Forward-looking information is subject to business, legal and economic risks and uncertainties and other factors that could cause actual results to differ materially from those contained in forward-looking statements. Such factors include, among other things, risks relating to property interests, the global economic climate, commodity prices, sovereign and legal risks, and environmental risks. Forward-looking statements are based upon estimates and opinions at the date the statements are made. Barton undertakes no obligation to update these forward-looking statements for events or circumstances that occur subsequent to such dates or to update or keep current any of the information contained herein. Any estimates or projections as to events that may occur in the future (including projections of revenue, expense, net income and performance) are based upon the best judgment of Barton from information available as of the date of this document. There is no guarantee that any of these estimates or projections will be achieved. Actual results will vary from the projections and such variations may be material. Nothing contained herein is, or shall be relied upon as, a promise or representation as to the past or future. Any reliance placed by the reader on this document, or on any forward-looking statement contained in or referred to in this document will be solely at the readers own risk, and readers are cautioned not to place undue reliance on forward-looking statements due to the inherent uncertainty thereof.

* Refer to Barton Prospectus dated 14 May 2021 and ASX announcement dated 11 December 2023. Total Barton attributable JORC (2012) Mineral Resources include 824koz Au (26.8Mt @ 0.96 g/t Au) in Indicated and 750koz Au (25.4Mt @ 0.92 g/t Au) in Inferred categories.

JORC Table 1 - Tunkillia Gold Project

Section 1 Sampling Techniques and Data

Criteria

Commentary

Sampling techniques

Nature and quality of sampling (e.g. cut channels, random chips, or specific specialised industry standard measurement tools appropriate to the minerals under investigation, such as down hole gamma sondes, or handheld XRF instruments, etc.). These examples should not be taken as limiting the broad meaning of sampling.

Include reference to measures taken to ensure sample representivity and the appropriate calibration of any measurement tools or systems used.

Aspects of the determination of mineralisation that are Material to the Public Report. In cases where ‘industry standard' work has been done this would be relatively simple (e.g. "RC drilling was used to obtain 1 m samples from which 3 kg was pulverised to produce a 30 g charge for fire assay"). In other cases, more explanation may be required, such as where there is coarse gold that has inherent sampling problems. Unusual commodities or mineralisation types (e.g. submarine nodules) may warrant disclosure of detailed information

Sampling during Barton Gold's RC drill programs at Tunkillia was obtained through reverse circulation (RC) and diamond drilling methods Historic RC and diamond drilling methods were also used in drilling campaigns completed since the mid-1990s.

Rotary air-blast (RAB) and aircore drilling has also been completed. These holes were used to guide interpretation but were not used modelling or grade estimations of the results reported in the accompanying Announcement.

The drilling program used a Metzke cone splitter (or similar) attached to the cyclone. One-metre splits were constrained by chute and butterfly valves to derive a 2-4kg split on the cyclone. Samples above 1m depth were not collected.

Diamond core for drilling has been sawn in half using an automated core saw. Field duplicates were derived from using quarter core for the designated interval.

Historic diamond core has been sawn in half or quarter using a core saw.

The sample preparation for drilling conducted in 2022 and 2023 of the one-metre sampling for Barton Gold's RC and diamond drill program was conducted by Bureau Veritas (Adelaide) using method FA1 where the 2-3kg split sample received at the laboratory is weighed, dried, crushed to 10mm, pulverized to 75 micron and split to provide a 40g sample for fire assay analysis.

The sample preparation of the one-metre sampling for Barton Gold's 2021 RC drill program was conducted by Intertek Genalysis (Adelaide) using method SP1 where the 2-3kg split sample received at the laboratory is weighed, dried, crushed to 3mm, pulverized to 75 micron and split to provide a 50g sample for fire assay and adequate pulverized material for multi-element

analysis.

For early RC drillholes (1996-1997), the 1 metre samples were collected through a cyclone and collected in poly bags. Samples were initially taken as 4 metre spear composites and then re-assayed at 1 metre intervals if the initial sample returned a grade above a certain threshold. RC drillholes drilled post-1997 were sampled through an on-rig splitter system The majority of core samples were taken as 1 metre lengths and half-cored.

Drilling techniques

Drill type (e.g. core, RC, open-hole hammer, rotary air blast, auger, Bangka, sonic, etc.) and details (e.g. core diameter, triple or standard tube, depth of diamond tails, face-sampling bit or other type, whether core is oriented and if so, by what method, etc.).

The RC drilling by Barton Gold used a face-sampling 5 ¾" RC drilling techniques undertaken by Kennedy Drilling using a SREPS SR650 drilling rig with auxiliary compressor.

Earlier RC drilling by Barton Gold (2021-22) contributing to the work reported was undertaken by Bullion Drilling utilising equivalent drilling equipment.

The diamond drilling program used a UDR1200 drill rig provided by Resolution Drilling, drilling NQ (47.6mm diameter) size drill core, using a standard tube configuration. Diamond drill holes were precollared with rotary mud drilling through the strongly weathered (clay) upper parts of each drill hole. Drill core was oriented (bottom of hole) using the Axis Champ orientation system.

Historically slimline RC drilling used a face-sampling hammer bit with a diameter of ~90mm. All other RC drillholes were drilled using a "standard size" hammer (ranging from 120mm-136mm). Diamond drillholes have been pre-drilled to fresh rock using a RC pre-collar or cored from surface, with a range of diameters used: NQ, PQ, HQ.

Drill sample recovery

Method of recording and assessing core and chip sample recoveries and results assessed.

Measures taken to maximise sample recovery and ensure representative nature of the samples.

Whether a relationship exists between sample recovery and grade and whether sample bias may have occurred due to preferential loss/gain of fine/coarse material.

During drilling programs drilling recoveries were qualitatively described for each drilled interval in the field database along with an estimation of moisture content. In general recoveries were good, in the order of 30-40kg for each one-metre interval. Water was encountered in some drill holes and wet samples were collected from some intervals, although wet samples comprise <3% of sampling overall. No reduced sample weights were recorded with wet intervals and a review of results does not indicate contamination between adjacent samples. Samples submitted to the laboratory were weighed on a dry, as-received basis and reported along with assay results.

Recoveries for diamond drill core were measured and recorded.

No quantitative recoveries were recorded from pre 2021 RC drilling. However, consistent sample weights were noted within mineralised zones in previous reports. No quantitative recoveries have been recorded from previous diamond drilling through mineralised zones. However, previous MRE and geological reports indicate there has been negligible loss through mineralised zones.

Recoveries of 90-100% were achieved in geotechnical drilling of the saprolite for geotechnical assessment.

The RC and diamond drilling was closely monitored by the site geologist to ensure optimal recovery and that samples were considered representative.

Historically, HQ triple tube (HQ3) drilling was used for some holes to maximise core recovery. Re-entry holes were not triple-tubed as they were drilled straight into fresh bedrock. Drilling rates were controlled, and short drill runs were often used through the oxide zone to maximise core recovery.

No relationship between grade and recovery has been identified.

Logging

Whether core and chip samples have been geologically and geotechnically logged to a level of detail to support appropriate Mineral Resource estimation, mining studies and metallurgical studies.

Whether logging is qualitative or quantitative in nature. Core (or costean, channel, etc.) photography.

The total length and percentage of the relevant intersections logged.

All drilling programs electronically logged a number of parameters direct into a database including: Stratigraphy, lithology, weathering, primary and secondary colour, texture, grainsize, alteration type-style-intensity and mineralisation type-style-percentage.

Historically RC chips and diamond core were logged by experienced geologists as a hard copy or into a DataShed database. From 2023 Barton has stored all drilling data in an in-house managed MS Access database. All diamond core was photographed. Structural measurements were made on core oriented using either a spear and Ezy-Mark (pre-Barton) or Reflex (Barton) core orientation devices. Core is stored on site and at the South Australian Government's Adelaide Core Library.

All diamond core and RC drilling has been geologically logged.

Subsampling techniques and sample preparation

If core, whether cut or sawn and whether quarter, half or all core taken

If non-core, whether riffled, tube sampled, rotary split, etc. and whether sampled wet or dry.

For all sample types, the nature, quality and appropriateness of the sample preparation technique.

Quality control procedures adopted for all subsampling stages to maximise representivity of samples.

Measures taken to ensure that the sampling is representative of the in-situ material collected, including for instance results for field duplicate/second-half sampling.

Whether sample sizes are appropriate to the grain size of the material being sampled.

Diamond drill core was sawn in half with one half taken for sampling. Sample lengths were generally 1m although at times were sampled to geological intervals.

Selected intervals of whole core were used for geotechnical test work.

The RC drilling program used an Ox sampling system (Kennedy) or Metzke (Bulion) cone splitter mounted on the cyclone with one-metre splits constrained by chute and butterfly valves to derive a 2-4kg split on the cyclone. The majority (>97%) of samples were dry and when samples were wet they were recorded in the sampling records.

The majority of the historical RC samples have been collected at 1 metre intervals using a rifle splitter attached to the drill rig. Periodically between 1996 and 2011, within the strongly weathered portion, samples were collected over 4m intervals. The sample was speared to achieve a representative portion from the interval.

During the RC drilling program a field duplicate was collected off a second chute on the cyclone splitter at a frequency of either 1 for each 16-original sample intervals (2021 drilling), 1 for each 22-orignal sample intervals (2022 drilling) or 1 for each 50-original sample intervals (2023 drilling).

Field duplicates for diamond core were obtained by submitting quarter core for the selected intervals (ie half core was retained for all field duplicate intervals)

Early drillholes up until 2006 utilised field duplicates and blanks as their only QAQC, this effectively accounts for 57% of the holes used in the current resource estimation.

Sample sizes are considered to be appropriate to the grain size of the material being sampled.

Quality of assay data and laboratory tests

The nature, quality and appropriateness of the assaying and laboratory procedures used and whether the technique is considered partial or total.

For geophysical tools, spectrometers, handheld XRF instruments, etc., the parameters used in determining the analysis including instrument make and model, reading times, calibrations factors applied and their derivation, etc.

Nature of quality control procedures adopted (e.g. standards, blanks, duplicates, external laboratory checks) and whether acceptable levels of accuracy (i.e. lack of bias) and precision have been established.

Barton Gold (2022-2023) - 2-4kg splits were sent to Bureau Veritas in Adelaide for preparation and analysis using 40g fire assay techniques for gold. Bureau Veritas' FA1 method uses a 40g lead collection fire assay with AAS finish to a 0.01 ppm detection limit.

Barton Gold (2021) - 2-4kg splits were sent to Intertek Genalysis in Adelaide for preparation and analysis using 50g fire assay techniques for gold and ICPOES/MS for multielement geochemistry. Whilst preparation and some fire assays were undertaken in Adelaide Intertek also sent some batches to their Perth laboratories for analysis. Intertek's FA50/OE04 method uses a 50 g lead collection fire assay with ICP-OES / MS finish to a 0.005 ppm detection limit. Multielement samples were analysed using Intertek's method 4A/MS48 which is a 4-acid digest followed by analysis using ICP-OES and MS for 48 elements.

Pre-2003 samples were sent to Analabs for analysis. Post 2003 samples were sent to Intertek Genalysis Laboratory for assay Gold values were determined by aqua regia digest (B/ETA or B/SAAS) and any values returning >1ppm were repeated using fire assay (FA25/AAS). If a fire assay was taken then this became the "official" assay. All other elements were determined using multi-acid digest (AT/OES)

Analytical techniques have varied somewhat over the projects history.

No geophysical studies were used in the course of Barton Gold drilling programs.

Barton Gold's RC and diamond drilling programs included a comprehensive QAQC component with Field Duplicate samples taken at every 16th (2021 drilling), 25th sample (2022 drilling) or 50th sample (2023 drilling); Certified Standards (selection of OREAS CRM's considered most appropriate for expected grade and composition) were inserted randomly in sequence for at every 20th (2021 drilling), 25th (2022 drilling) or 50th sample (2023) submitted; blanks were inserted in sequence at every 50th sample submitted. Additionally, the laboratories provided their internal QAQC which included check samples, CRM's, blanks and repeats.

Analysis of the duplicate samples was reasonable given the majority fell below detection. Variances between some higher grade pairs of field duplicates was recorded, but attributed to variability in the distribution of mineralisation (vein related) and not as a consequence of analytical processes. There was no evidence of material cross-contamination in the submitted blank samples.

Both Intertek and Bureau Veritas' analysis for gold using fire assay performed well with all batches falling within the +/-3SD test of the expected value for the given standards (3 OREAS CRM's).

Historically, the amount of sampling and analytical QC data that has been collected has varied over the project's history. Early drillholes up until 2006 utilised field duplicates and blanks as their only QAQC, this effectively accounts for 57% of the holes used in the estimation. Post 2006, QAQC samples were submitted in the form of field duplicates and Certified Reference Standards from Ore Research & Exploration Pty Ltd. Standards were submitted every 20th sample and field duplicates every 50th sample. No material concerns were highlighted in the analysis of QAQC data.

Tunkillia Gold used blanks to monitor carry-over contamination and no significant issues were detected. Field duplicates were used to assess sample precision, while CRMs were used to assess analytical accuracy. Some pulps were also sent to an umpire laboratory as a further check on analytical accuracy.

Field duplicate results provide a guide to sample precision. The expected scatter (due to high nugget effect) is monitored and is expected to remain within a range. The CRMs reasonably demonstrated the accuracy of the laboratory. Pulp repeats demonstrated acceptable performance.

Verification of sampling and assaying

The verification of significant intersections by either independent or alternative company personnel.

The use of twinned holes.

Documentation of primary data, data entry procedures, data verification, data storage (physical and electronic) protocols.

Discuss any adjustment to assay data.

Alternative company personnel have verified significant intersections.

No twinned holes were undertaken on the 2023 program reported in this release.

One previous Barton RC hole has been twinned by a diamond hole, confirming the position of the mineralised envelopes and grade characteristics in the system.

Location of data points

Accuracy and quality of surveys used to locate drillholes (collar and downhole surveys), trenches, mine workings and other locations used in Mineral Resource estimation.

Specification of the grid system used.

Quality and adequacy of topographic control.

All data collected in the reported program including collar details, drilling records, sampling records and geological logs are recorded directly into spreadsheets in the field which includes comprehensive interval validation processes.

Gyro downhole surveys and Assay results were provided in digital format.

All relevant historical data was entered into a DataShed database where various validation checks were performed. Data was exported into an Access Database.

No adjustments were made to any assay data in this release.

All Q4 2023 RC and diamond drill collars were sited using a Garmin hand-held GPS system. Prior drillholes were similarly sited with a Garmin Hand-held GPS system and subsequently picked up with a Leica DGPS system. The RL was generated from the LiDAR survey collected at the completion of drilling.

All Barton RC holes were downhole surveyed using an Axis Champ gyro system which provided measurements at 10m intervals up and down hole.

All Barton diamond holes were surveyed using a single-shot gyro tool at 15m or 30m intervals during drilling operations.

488 out of a total of 556 drillhole collars from drilling prior to 2021 across the broader Tunkillia project were located using DGPS survey techniques. The raw data for 30% of these have been located and verified. Earlier collars were located by measuring off a local grid system.

All site data is reported in Geocentric Datum of Australia 1994 (GDA94) and Vertical Datum in Australian Height Datum (AHD). The map projection is MGA Zone 53. Historic Survey Data has been converted to GDA94.

Historically the Tunkillia Project uses the Remington local grid which is rotated 31.37 degrees west of the MGA 94 grid with a local origin of 110,000E and 111,500N

Transformation Formula:

Local E = 110000 + ((MGA94_E - 477614.802 ) cos a) + ((MGA94_N - 6545289.018) sin a))

Local N = 111500 + ((MGA94_N - 6545289.018) cos a) - (MGA94_E - 477614.802) sin a))

Where angle a = 31.37

Local RL = mRL_MGA+1009.232

In September 2021 Barton engaged Aerometrex to collect LiDAR and high-resolution ortho-imagery over the entire Tunkillia project area. All datasets are levelled to the LiDAR survey

Data spacing and distribution

Data spacing for reporting of Exploration Results.

Whether the data spacing and distribution is sufficient to establish the degree of geological and grade continuity appropriate for the Mineral Resource and Ore Reserve estimation procedure(s) and classifications applied.

Whether sample compositing has been applied.

Barton's RC and diamond drilling program at the A51 project was conducted at variable spacing as dictated by existing drilling and the aims of the program to provide continuity with the existing drill coverage. Drilling has been undertaken on lines spaced a nominal 50m apart. The spacings are considered appropriate for the reporting of exploration results.

On section drill spacing generally ranges from 20-30m, increasing to 50 metres with the majority of drilling on section and perpendicular to strike.

Orientation of data in relation to geological structure

Whether the orientation of sampling achieves unbiased sampling of possible structures and the extent to which this is known, considering the deposit type.

If the relationship between the drilling orientation and the orientation of key mineralised structures is considered to have introduced a sampling bias, this should be assessed and reported if material.

Barton's RC and diamond drill program was orientated to optimally test predicted mineralised structures and stratigraphic positions to provide were possible unbiased samples.

Drill sections are orientated local grid E-W, perpendicular to the main mineralised lenses.

The majority of drillholes used to define the steeply west dipping primary mineralisation are drilled towards the east at -60 degrees.

The relationship between the drilling orientation and the orientation of key mineralised structures is not considered to have introduced a sampling bias.

Sample security

The measures taken to ensure sample security.

Barton Gold staff oversaw the sampling on the RC drill rig and maintained oversight of sample security whilst onsite during the drilling programs. Split samples were inserted into pre-printed calico bags. These tied bags were, in batches of 5, ziplocked into labelled poly-weave bags which were inserted into ziplocked Bulka-bags. The bulka bags were strapped onto pallets and loaded by a Barton Gold representative on to a semitrailer for transport to the laboratories in Adelaide and Perth. The trailers were not unloaded whilst in transit.

Diamond drill core was either cut on site or transported from the project site to Adelaide and cut by experienced and reputable service providers. The core cutting agents undertook sampling of the drill core and subsequent delivery of samples to the laboratory. Barton Gold staff undertook regular visits during core cutting and sampling processes to verify the integrity of processes being undertaken.

Barton does not have detailed information in regard to sample security measures taken by previous owners of the Tunkillia project. However, Barton understands that these procedures have been in accordance with commonly adopted standard industry practices.

Audits or reviews

The results of any audits or reviews of sampling techniques and data

An internal peer review of the exploration data processes has been completed by Barton Gold which has included a detailed review of the assay, survey and QAQC data.

Section 2 Reporting of Exploration Results

Criteria

Commentary

Mineral tenement and land tenure status

Type, reference name/number, location and ownership including agreements or material issues with third parties such as joint ventures, partnerships, overriding royalties, native title interests, historical sites, wilderness or national park and environmental settings.

The security of the tenure held at the time of reporting along with any known impediments to obtaining a licence to operate in the area.

The Tunkillia Project area is located 530 km north-west of Adelaide in South Australia's Gawler Craton. It is 100% owned by Tunkillia 2 Pty Ltd which is a wholly owned subsidiary of Barton Gold Holdings Limited.

The project comprises two exploration licences that were grouped into an Amalgamated Expenditure Agreement on 4th October 2012 and Joint Venture Reporting on 21st January 2013.

Most of the South Australian tenements held by WPG Resources were bought by current owner Barton Gold Pty Ltd on 1st November 2019.

The three current tenements comprise EL6845, EL6639 and EL5901 which have a combined area of 1,362 km2.

The Tunkillia Project was under three overlapping Native Title claims which are now grouped into a single organisation, the Gawler Ranges Aboriginal Corporation (GRAC) that represents all three groups.

Barton Gold's negotiations with GRAC secured a signed Native Title Mining Agreement for Exploration for EL's 6845, EL6639 and EL5901 on 2nd February 2021.

Barton's Exploration Licences 6845, 6639 and 5901 are subject to South Australian State royalties and entitled to a reduced ‘new mine' State royalty rate of 2% of the value of minerals recovered until 30 June 2026, and are also subject to total 2.5% private royalties (gross product).

There are no joint ventures over the Tunkillia Project tenure.

There are no known impediments to obtaining future licences.

Exploration done by other parties

Acknowledgment and appraisal of exploration by other parties.

Exploration in the Tunkillia area commenced in 1996 with a regional geochemical survey by Helix Resources who established the local Remington grid. Infill sampling delineated the Tunkillia Prospect as a 20 km2 geochemical gold in calcrete anomaly. Subsequent RAB drilling led to the discovery of the Area 223 deposit in late 1996. RC drilling in early 1997 further enhanced the discovery.

A joint venture was formed with Acacia who took over management of the project with subsequent exploration carried out as the Gawler Craton Joint Venture. The JV later involved AngloGold Australasia Ltd following its takeover of Acacia.

In June 2003, Helix finalised the acquisition of AngloGold's 49% interest and returned 100% of the project to Helix

An independent resource assessment by Snowden Mining Industry Consultants prompted an extensive 12,000m RC program to infill the Area 223 resource. A re-interpretation of the aeromagnetic data identified new exploration targets away from the known resource outlining mineralisation at Tomahawk and Areas 191.

In April-June 2004 Helix completed an 8000 m RC drilling program testing areas of the Area 223 North and South mineralisation and exploration concepts at Area 191 and the central part of the shear zone.

Studies were completed by Resource Evaluations Pty Ltd in June 2004 looking at resource estimates and optimisation studies based on the available drilling.

A Joint Venture commenced between Helix and Minotaur Exploration Ltd in April 2005 where Minotaur assumed operation and management of the project. Minotaur undertook an intense exploration effort in the immediate surrounds of the Area 223 resource, and regionally.

In 2007, Minotaur re-appraised the Area 223 resource using recent drilling and separated distinct oxide and sulphide domains.

In January 2012, Mungana acquired the 55% interest in the Tunkillia Gold Project via the acquisition of Minotaur's wholly owned subsidiary Minotaur Ventures Pty Ltd.

WPG Resources acquired 70% of the project in May 2014 through the acquisition of the Tarcoola and Tunkillia projects from Mungana Goldmines Ltd. In Nov 2014 WPG moved to 100% ownership of the Tunkillia gold project by acquiring the 30% owned by Helix Resources.

WPG Resources completed work on calcrete samples over a number of targets along the Tunkillia "Line of Lode". Drilling of selected Area 51 and Tomahawk Extended areas included ten RC holes for 1,641m. No further work was undertaken by WPG Resources until the project was purchased by Barton Gold in late 2019.

Geology

Deposit type, geological setting and style of mineralisation.

The Tunkillia Project extends over a large portion of the Central Gawler Craton of South Australia which is bound to the east by the Gawler Range Volcanic Province.

The central portion of the Gawler Craton consists of a variety of geological units and is structurally complex. Archaean metamorphic rocks and greenstone-belt units are distributed along WSW-ENE trends. During the Palaeoproterozoic, granitoids including the Tunkillia Suite were emplaced possibly with associated deformation. During these deformation episodes, major shear zones developed, including the east-trending Yerda and Oolabinnia Shear Zones and north-trending Yarlbrinda Shear Zone.

The Yarlbrinda Shear Zone and Yerda Shear Zone are up to several kilometres wide with ductile shearing and deformation probably occurring before ~1600 Ma and before Mesoproterozoic anorogenic magmatism.

During the Mesoproterozoic, widespread anorogenic magmatism across the central portion of the craton resulted the Gawler Range Volcanics, Hiltaba Suite granite (1595-1575 Ma) and emplacement of minor gabbroic plugs.

Development of Cu-Au +/- U mineralisation at Olympic Dam and Prominent Hill and gold dominant mineralisation at Tunkillia and Tarcoola occurred during this period.

Typical lithologies encountered across the Tunkillia project (including Area 51) from west to east include variably sheared chlorite-biotite-rich augen gneiss (Tunkillia Augen Gneiss) grading into a highly chloritised and mylonitised phyllonitic shear. The phyllonitic shear zone grades into a weakly gneissic unit to the east which is variably altered by sericite to form the central alteration zone. This unit has a sheared contact with the footwall granite.

The host rocks have been intruded by at least two later episodes of dyke emplacement. The mafic dyke appears to form the footwall to the main mineralisation at Area 223.

Relationships between dyke emplacement and the mineralisation remain unclear. The dykes appear to cross-cut mineralisation at most of the Tunkillia project prospects and deposits and are unmineralised in fresh rock. But in the weathered zone gold occurs within the weathered dyke and also to east of this apparent ‘bounding' lithology.

The main mineralisation appears to occur within en-echelon sets of quartz-sulphide tension veins predominately bounded by duplex shears, with brittle fractures extending into the hanging wall.

The mineralised positions across the Tunkillia project has undergone extensive weathering which formed a leached kaolinitic profile capped by a silcrete layer. No palaeochannels are observed at Area 223 or Area 51 although they do occur elsewhere in the Tunkillia area.

At 50-60 metres depth near the base of the weathering profile a zone of supergene mineralisation is developed which shows some enrichment compared with the underlying primary lodes. Gold appears to have been laterally dispersed over a distance of tens of metres within the oxide zone.

Drillhole information

A summary of all information material to the understanding of the exploration results including a tabulation of the following information for all Material drillholes:

  • Easting and northing of the drillhole collar
  • Elevation or RL (Reduced Level - Elevation above sea level in metres) of the drillholecollar
  • Dip and azimuth of the hole
  • Downhole length and interception depth hole length.

If the exclusion of this information is justified on the basis that the information is not Material and this exclusion does not detract from the understanding of the report, the Competent Person should clearly explain why this is the case.

No new drilling is reported in this release. All drilling has previously been reported to the market.

Data aggregation methods

In reporting Exploration Results, weighting averaging techniques, maximum and/or minimum grade truncations (e.g. cutting of high grades) and cut-off grades are usually Material and should be stated.

Where aggregate intercepts incorporate short lengths of high grade results and longer lengths of low grade results, the procedure used for such aggregation should be stated and some typical examples of such aggregations should be shown in detail.

The assumptions used for any reporting of metal equivalent values should be clearly stated.

No new results are reported in this release and previously reported intersections used the following criteria:

  • Reported intervals have been determined by applying either
  • a) a 0.5g/t Au cut-off (minimum 1gram-metre accumulation, ie the multiple of the interval in metres and the weighted average grade) and allowing for a maximum of two consecutive intervals of dilution, OR.
  • b) a 0.3g/t Au cut-off (minimum 5gram-metre accumulation) and allowing for a maximum of two consecutive intervals of dilution. This is considered appropriate to convey the significant widths of mineralisation that characterise parts of the Tunkillia project
  • No high-grade cut-offs were applied
  • Results for quarter-core field duplicates from diamond drilling were averaged across the pair of samples to provide a result consistent with routine half-core sampling
  • No metal equivalents were calculated

Relationship between mineralisation widths and intercept lengths

These relationships are particularly important in the reporting of Exploration Results.

If the geometry of the mineralisation with respect to the drillhole angle is known, its nature should be reported.

If it is not known and only the down hole lengths are reported, there should be a clear statement to this effect (e.g. "downhole length, true width not known").

Drillholes have been designed to intersect the mineralisation zone as perpendicular as possible. Reported intercepts are downhole length and true width can generally be estimated because the dip of the mineralisation is known.

Diagrams

Appropriate maps and sections (with scales) and tabulations of intercepts should be included for any significant discovery being reported These should include, but not be limited to a plan view of drillhole collar locations and appropriate sectional views.

See Figures included the body of this Announcement. Relevant commentary relating to diagrams is discussed under the heading of Balanced Reporting.

Balanced reporting

Where comprehensive reporting of all Exploration Results is not practicable, representative reporting of both low and high grades and/or widths should be practiced to avoid misleading reporting of Exploration Results.

Balanced reporting of Exploration Results is presented

Other substantive exploration data

Other exploration data, if meaningful and material, should be reported including (but not limited to): geological observations; geophysical survey results; geochemical survey results; bulk samples - size and method of treatment; metallurgical test results; bulk density, groundwater, geotechnical and rock characteristics; potential deleterious or contaminating substances.

Extensive geological, geophysical, geochemical, geotechnical and metallurgical datasets are available for the Tunkillia project area.

Other datasets including gravity that was sourced from open-file datasets (SA DEM).

Historical data acquired by previous owners included detailed aeromagnetic, TEMPEST airborne EM and in-fill gravity surveys completed over parts of the tenement area and mostly focussed on the Yarlbrinda Shear Zone.

Other data includes gradient array IP, biogeochemical sampling, CHIM/MMI geochemical sampling and spectral scanning of reverse circulation drill chips.

Further work

The nature and scale of planned further work (e.g. tests for lateral extensions or depth extensions or large-scale step-out drilling).

Diagrams clearly highlighting the areas of possible extensions, including the main geological interpretations and future drilling areas, provided this information is not commercially sensitive.

Mineralisation at the deposits and prospects across the Tunkillia project remains open along strike and downdip with potential for additional gold mineralisation at the Area 223 deposit and in other parallel structures in the area including Area 51, Tomahawk and Area 191. Barton Gold is planning further drilling work which will be focused on testing for dip and strike extensions and to confirm grade and geological continuity within the current models.

While geophysical coverage already exists, additional geophysical exploration techniques may be undertaken as the project continues and may include magnetic surveys and ground-based gravity.

Diagrams have been included in the body of this Announcement.

Section 3 Estimation and Reporting of Mineral Resources

Criteria

Commentary

Database integrity

Measures taken to ensure that data has not been corrupted by, for example, transcription or keying errors, between its initial collection and its use for Mineral Resource estimation purposes.

Data validation procedures used.

Barton Gold has undertaken limited independent first principal checks using hard copies of results and sectional interpretations. Plots of the sections were provided to MA, to guide the interpretation.

Historical Independent Technical Reports accept the integrity of the database.

The geological database has been managed by several different database management providers over the years. The database is currently managed by the Barton Gold using MS Access. Preceding historic data was obtained from open file reports.

MA undertook basic database validation checks were run, including collar locations, drill holes plot on topography, checks for missing intervals, overlapping intervals and hole depth mismatches.

Site visits

Comment on any site visits undertaken by the Competent Person and the outcome of those visits.

If no site visits have been undertaken indicate why this is the case.

The Competent Person (CP, Mr I.Taylor) visited site from the 1st to 4th November 2022 during the 2022 drill program to review the geology, drill core, field and drill practices. The site visit included Area 51, and drilling that had occurred to that date.

Data collection and discussions with the site geologists were the primary focus of the visits, a greater understanding of the geological setting and appreciation of Barton's Gold Procedures.

Geological interpretation

Confidence in (or conversely, the uncertainty of) the geological interpretation of the mineral deposit.

Nature of the data used and of any assumptions made.

The effect, if any, of alternative interpretations on Mineral Resource estimation.

The use of geology in guiding and controlling Mineral Resource estimation.

The factors affecting continuity both of grade and geology.

Confidence in the geological interpretation is considered moderate to high, dependent on the differing drill hole spacing in parts of the deposit. Two diamond core holes have been drilled into Area 51.

Interpretations are based solely on drill hole data: there is no outcrop in the area covering the deposit. All assayed drill metres are RC. Diamond holes are strategically placed for maximum structural understanding.

Drill core and RC chip logging has been used to define the main geological units and weathering profile boundaries.

Observations from diamond drill core indicate that mineralized veins generally overprint (but can also be concordant to) a pervasive shear foliation present in granitic host rocks.

Alternative interpretations of mineralized domain boundaries would affect tonnage and grade, although the CP is confident that the current model is the best representation of the deposit based on available data.

Four fresh rock mineralized structures were interpreted, based on continuity of grade at a lower cut-off of 0.35 g/t Au at the A51 deposit.

Structures were grouped into geostatistical domains based on grade similarities and structural orientation. Area 51 strikes grid (local) north-south and dip steeply west.

Minor cross faulting is likely to exist at the project, the offsets are considered too small to quantify on the current drill spacing.

Additional work is required to determine the nature of the structural controls on mineralised domain boundaries.

Dimensions

The extent and variability of the Mineral Resource expressed as length (along strike or otherwise), plan width, and depth below surface to the upper and lower limits of the Mineral Resource.

The Area51 deposit is defined with approximately 1000 m strike and is between five and 10 metres thick on the main structure and up to hundred metres wide in the overlying oxide mineralisation. The depth of the deposit had been defined beyond 300 m below the surface. The reported resource has been reported to 150 m below the surface.

Mineralisation strikes NW (UTM) and dips steeply to the SW ~80°.

The shear structure and contained mineralisation are expected to propagate to depth and are open.

Estimation and modelling techniques

In the case of block model interpolation, the block size in relation to the average sample spacing and the search employed.

Any assumptions behind modelling of selective mining units.

Any assumptions about correlation between variables.

Description of how the geological interpretation was used to control the resource estimates.

Discussion of basis for using or not using grade cutting or capping.

The process of validation, the checking process used, the comparison of model data to drill hole data, and use of reconciliation data if available.

The deposit is drilled on 50 m sections with up to 3 drill holes spaced 25 m along sections resulting in 50 m pierce points.

MA chose a smaller parent block size of 10 x 20 x 5 m, approximating ½ the dominant drill spacing. The likely finial mining scenario, (open pit benches), prompted the selection of sub blocks reflecting a likely SMU of 1.25 x 2.5 x 1.25 m (XYZ))

Search ellipses were based on variogram ranges and ranged between 70 and 90 m on the long axis.

A two pass estimation process was employed, the first pass required a minimum of 12 samples and a maximum of 20 composites, the second pass (double the search) required a minimum of 6 composites and a maximum of 16 composites. 67% of the tonnes are estimated during the first pass.

The deposit is best suited to open pit mining methods, the sub block size chosen (1.25, 2.5, 1.25m (XYZ) was chosen to reflect a reasonable smallest mining unit assuming 5 m blasts and 2.5 flitches. The smallest mining unit also was considered when selecting appropriate composite lengths.

Gold and silver mineralisation are well correlated. However silver mineralisation is too low a grade to be economically significant. Samples are not routinely assayed for Silver.

The geological model included weathering profiles. Mineralisation above the base of weathering is assumed to be affected by supergene or weathering effects and is interpreted as dominantly horizontal lenses. The base of weathering is considered a hard boundary during interpretation. No post mineralisation dykes are present at A51.

1 m composite assays were reviewed, extreme outliers were checked against primary assay results and in relation to the remainder of the domain.

Global drill hole and sample means were compared. Localised Swath plots were checked, both at the deposit scale and domains scale.

Grade tonnage curves from a Nearest neighbour and ID2 estimate were compared to the OK grade tonnage curve.

No mining has occurred at the project.

Moisture

Whether the tonnages are estimated on a dry basis or with natural moisture, and the method of determination of the moisture.

Tonnages are based on dry tonnes. Dry bulk density has been assigned to the host rock.

Cut-off parameters

The basis of the adopted cut-off grade(s) or quality parameters applied.

The resource is reported above a 0.5 g/t Au lower cut-off. Considering likely open pit mining, conventional heap leach or CIL processing and administration costs a head grade of 0.40 g/t is assumed profitable.

Key Assumptions:

• Open pit mining method

• 1.25m minimum mining width (sub block width),

• 5:1 strip ratio

• Mining and Processing cost of AUD$33.24/tonne for mineralised material.

• Gold price AUD 3,000/oz

• 95% Metallurgical recovery

• 5.0% Dilution

• 6.0% Royalty

• This is in line with assumptions used in previous Pre-Feasibility Studies. The metal price used was AUD 3,000/oz..

Mining factors or assumptions

Assumptions made regarding possible mining methods, minimum mining dimensions and internal (or, if applicable, external) mining dilution. It is always necessary as part of the process of determining reasonable prospects for eventual economic extraction to consider potential mining methods, but the assumptions made regarding mining methods and parameters when estimating Mineral Resources may not always be rigorous. Where this is the case, this should be reported with an explanation of the basis of the mining assumptions made.

No mining factors or assumptions have been applied to the resource.

MA considers the A51 deposit amenable to open pit mining methods. MA considers A51 to be a satellite deposit to the Tunkillia Project, the likely mining scenario will be in conjunction with the Tunkillia deposit. The pit is envisaged to have a 5 m benches and 2.5 m flitches. These assumptions have influenced, composite length, block size and resource cut off parameters.

Metallurgical factors or assumptions

The basis for assumptions or predictions regarding metallurgical amenability. It is always necessary as part of the process of determining reasonable prospects for eventual economic extraction to consider potential metallurgical methods, but the assumptions regarding metallurgical treatment processes and parameters made when reporting Mineral Resources may not always be rigorous. Where this is the case, this should be reported with an explanation of the basis of the metallurgical assumptions made.

No metallurgical factors have been applied to the in-situ grade estimates.

Metallurgical Recovery is assumed, and a 95% gold recovery is used in the reasonable prospects of economic extraction analysis, no account of silver recovery is considered.

Four campaigns of metallurgical test work have been commissioned over the life of the Tunkillia project (1997,2006, 2009,2013), none directly on A51 material but mineralisation is along strike of Tunkillia and similar in nature.

Gold recovery in fresh (Primary) ranges between 81 and 93% and in oxide between 92 to 97% recovery using different scenarios on Tunkillia Mineralisation.

The 2009 and 2013 studies showed adding a gravity circuit does not improve recovery.

Heap Leach recovery of the Tunkillia deposit is 76% in oxide material and low 30% in fresh material.

Environmental factors or assumptions

Assumptions made regarding possible waste and process residue disposal options. It is always necessary as part of the process of determining reasonable prospects for eventual economic extraction to consider the potential environmental impacts of the mining and processing operation. While at this stage the determination of potential environmental impacts, particularly for a greenfields project, may not always be well advanced, the status of early consideration of these potential environmental impacts should be reported. Where these aspects have not been considered this should be reported with an explanation of the environmental assumptions made.

Environmental baseline mapping has not identified any matters that are likely to preclude the future development of a mining operation that requires the on-site management of wastes and process residues (waste rock and process tailings). The consideration of a conventional open-cut mining and CIP gold processing operation, including associated ancillary activities and stand-alone infrastructure at the Tunkillia Project, fits within the scope of the South Australian government's approval frameworks and processes for a project such as the Tunkillia deposit. The A51 deposit is approximately 2 Km north of the Sutton Hoo deposit and 4.5 km north of the Tunkillia 223 deposit.

Audits or reviews

The results of any audits or reviews of Mineral Resource estimates.

There has been no independent audit of the data or mineral resource.

Discussion of relative accuracy/confidence

Where appropriate a statement of the relative accuracy and confidence level in the Mineral Resource estimate using an approach or procedure deemed appropriate by the Competent Person. For example, the application of statistical or geostatistical procedures to quantify the relative accuracy of the resource within stated confidence limits, or, if such an approach is not deemed appropriate, a qualitative discussion of the factors that could affect the relative accuracy and confidence of the estimate.

The statement should specify whether it relates to global or local estimates, and, if local, state the relevant tonnages, which should be relevant to technical and economic evaluation. Documentation should include assumptions made and the procedures used.

These statements of relative accuracy and confidence of the estimate should be compared with production data, where available.

No geostatistical confidence limits have been estimated. The relative accuracy and confidence in the Mineral Resource Estimate is reflected in the Resource Categories.

The ordinary kriging result, due to the high level of smoothing, should only be regarded as a global estimate, and is suitable as a life of mine planning tool. High grade domains were used to restrict the high grade material.

Inferred Mineral Resource has a lower level of confidence than that applying to an Indicated Mineral Resource and must not be converted to an Ore Reserve.

Should local estimates be required for detailed mine scheduling techniques such as Uniform conditioning or conditional simulation should be considered, ultimately grade control drilling is required.

Comparison with the previous estimates indicates that the changes implemented in the current Mineral Resource Estimate produced results that are in line with expectations.

No mining has occurred at the A51 deposit.

SOURCE: Barton Gold Holdings Limited



View the original press release on accesswire.com



View the original press release on accesswire.com

ACCESSWIRE

News network reaching more than 1,500 media outlets in 98 countries. The newest, fastest-growing and most disruptive newswire available today.